How To Turn On Minn Kota Remote

ENGAGING SPOT LOCK

Press the Spot Lock push on the remote.
The Retentivity Location icon volition flash on the remote LCD for iii seconds, allowing you to cull a memory location by pressing the Speed Up or Speed Downwards buttons. Pressing the Spot Lock push again or waiting for three seconds accepts the retentivity location.

DISENGAGING SPOT LOCK

To disengage Spot Lock press any of these buttons:

RE-ENGAGE A SAVED SPOT LOCK LOCATION

Manually navigate the boat to within a quarter mile of the saved Spot Lock location. Due to prophylactic reasons,i- Pilot will non re-engage a saved Spot Lock location greater than a quarter mile away.
Printing the Spot Lock Think button on the remote.
The Memory Location icon will flash on the remote LCD for three seconds allowing you to choose a memory location by pressing the Speed Up or Speed Down buttons. Pressing the Spot Lock Call back button again or waiting for 3 seconds accepts the memory location.

SPOT LOCK ESCAPE

If the Spot Lock push button is accidentally hit, printing the Record Interruption/Escape button or whatsoever manual navigation button inside three seconds to abolish the command.

ENGAGING CRUISE Control

Printing the Prowl Control button on the remote.
The current GPS speed will flash, displaying your current speed as the target GPS speed on the remote LCD for three seconds.
Press the Speed Upward or Speed Down buttons to increase or decrease the target speed or press the Cruise Control button over again to engage Cruise Control immediately.

Disengage CRUISE Command

ADJUSTING TARGET SPEED WITH Prowl Control ENGAGED

With Cruise Control engaged press the Speed Up or Speed Down buttons to arrange the target speed by 0.ane MPH increments.

ENGAGING Avant-garde AUTOPILOT AND AUTOPILOT

To engage Avant-garde AutoPilot, press the AutoPilot button once. To engage AutoPilot, press and hold the AutoPilot push button for two seconds.
The Advanced AutoPilot or AutoPilot icon will be displayed on the remote LCD.
To adjust desired heading, manually steer motor to new heading. i-Airplane pilot will lock onto new heading.

RECORDING A Track

Press the Record button on the remote.
The Retentiveness Location icon will flash on the remote LCD for three seconds, allowing you to choose a memory location by pressing the Speed Upwards or Speed Down buttons. Pressing the Record button over again or waiting for iii seconds accepts the memory location.
The REC icon will be displayed on the remote LCD. Remember this will be the get-go betoken on the runway.
Navigate the boat along the desired path or class. AutoPilot and/or Cruise Control can be used while recording a runway.
Press the Record push on the remote once again to stop the recording. The recording volition finish automatically if the two-mile distance limit is reached for the track or if i of the following buttons are pressed: Spot Lock, Spot Lock Recall, Track to Stop or Track to Outset.

Interruption AND RESUME A RECORDING

While recording a rail printing the Record Pause/Escape button.
The tape icon will flash on the remote LCD.
i-Airplane pilot has now paused the recording of the track.
If the gunkhole moves farther than a quarter mile from where the Tape Pause/Escape button was pressed, the recorded track will exist ended and saved to the memory location previously selected.
When fix to resume recording, navigate the boat just ahead of where the Tape Intermission/Escape button was pushed. Failure to do this may cause erratic play back of a rails.
Push the Record Pause/Escape button.
The record icon will stop flashing on the remote LCD.
i-Airplane pilot is at present recording once again and calculation to the rails that was paused.

REPLAYING A Rails(Track TO Beginning / TRACK TO Terminate)

Manually navigate the boat to within a quarter-mile of the saved track. Due to safety reasons, i-Pilot will not re-engage a saved track greater than a quarter-mile away.
Press the Rails to Commencement or Track to End button on the remote.
The Retentiveness Location icon will flash on the remote LCD for three seconds, allowing y'all to cull a memory location by pressing the Speed Up or Speed Downward button. Pressing the button pressed in step 2 again or waiting for 3 seconds accepts the memory location.
Adapt motor speed to desired setting to engage and navigate rail automatically.

Ezoic

RECORD, TRACK TO Cease AND Rail TO Offset ESCAPE

If the Record, Track to Offset or Rail to End push is accidentally hit, press Record Pause/Escape button within three seconds on the remote to cancel the command.

Source: https://manuals.plus/minn-kota/i-pilot-remote-legacy-remote-manual

Iklan Atas Artikel